Is AD 2006-17-07 a recurring Airworthiness Directive?

Yes — AD 2006-17-07 requires a repetitive inspection. Next-due depends on the aircraft's time in service.

Which aircraft does AD 2006-17-07 apply to?

AD 2006-17-07 applies to Pratt & Whitney — models JT8D-1, JT8D-1A, JT8D-1B, JT8D-7, JT8D-7A, JT8D-7B, JT8D-9, JT8D-9A. Serial/part conditions may narrow it to specific aircraft.

Airworthiness Directive 2006-17-07

recurring

Official AD 2006-17-07 · FR doc E6-14238 · 2006-08-30 · turbine engine

Airworthiness Directives; Pratt & Whitney JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, -11, -15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and -219 Turbofan Engines

What this AD requires

The FAA is superseding an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-209, -217, -217A, -217C, and -219 turbofan engines. That AD currently requires initial and repetitive visual inspections for fretting and fluorescent magnetic particle inspections (FMPI) for cracking in the area of the tierod holes on 8th stage high pressure compressor (HPC) front hubs (from here on, referred to as HPC front hubs) that have operated at any time with PWA 110-21 coating. This AD requires either replacing HPC front hubs and HPC disks that have operated at any time with PWA 110-21 coating and that operated in certain engine models, or, visually inspecting and FMPI for cracking of those parts and re-plating them if they pass inspection. This AD also requires adding JT8D-1, -1A, -1B, -7, -7A, -7B, -9, -9A, - 11, -15, -15A, -17, -17A, -17R, and -17AR engines to the applicability. This AD results from an investigation by PW, which concluded that any HPC front hub or HPC disk coated with PWA 110-21 that ever operated on JT8D-15, -15A, -17, -17A, -17R, -17AR, -209, -217, -217A, -217C, and - 219 turbofan engines, could crack before reaching their published life limit. We are issuing this AD to prevent a rupture of an HPC front hub or an HPC disk that could result in an uncontained engine failure and damage to the airplane.

Repetitive inspection. Re-inspect. The next-due date/hours depend on this aircraft’s time in service — a records report computes it from the logbooks.

Which aircraft AD 2006-17-07 applies to

MakesPratt & Whitney

ModelsJT8D-1, JT8D-1A, JT8D-1B, JT8D-7, JT8D-7A, JT8D-7B, JT8D-9, JT8D-9A, JT8D-11, JT8D-15, JT8D-15A, JT8D-17, JT8D-17A, JT8D-17R, JT8D-17AR, JT8D-209, JT8D-217, JT8D-217A, JT8D-217C, JT8D-219, JT8D

Applicability keyed to 8th stage HPC front hub coating (PWA 110-21 or Nickel-Cadmium) combined with the stage 8-9 spacer coating and the specific engine model, per the applicability matrix in Table 1 of the AD. Installed on, but not limited to, Boeing DC-9, MD-80 series, 727 series, and 737 series airplanes.

Whether AD 2006-17-07 actually applies to your aircraft (by serial and installed parts) and whether it’s already complied with comes from that aircraft’s records.

How AD compliance is recorded

A valid compliance record (14 CFR 43.9) states:

Method of compliance — The specific action taken (inspected, replaced, modified) and to what revision.

Date — When the work was done.

Aircraft time — Total time in service / tach at compliance — how recurring next-due is computed.

Signature & certificate — The A&P/IA who returned it to service, with certificate number.

Is AD 2006-17-07 complied with on your aircraft?

Tailplate reads a tail number’s logbooks and matches every applicable AD — including this one — to its compliance evidence, with recurring next-due dates computed.

Look up a tail number →Read the full directive (Federal Register)

Applicability is derived from the FAA directive corpus and is advisory, not a legal airworthiness determination. Compliance is established only from an aircraft’s actual records.